|
Model T
Industrial-Duty Trolley Operator for
Standard Lift Sectional Doors
The
Model T is an industrial-duty trolley operator for
standard lift section doors. It features a low profile
and industrial ball bearings on the output shaft.
-
Built-in
3-channel, 315MHz radio receiver accepts up to 23
Security+® or unlimited DIP switch remotes. 3-button
remotes can be programmed for OPEN/CLOSE/STOP
operation
-
Maintenance Alert System™ establishes a routine
maintenance schedule based on the number of cycles
or calendar date. Includes self-diagnostic system
that allows you to troubleshoot up to eight
different error codes
-
Timer-to-Close allows programming in 5-sec or
1-min increments. Commercial or industrial
photo-eyes required
-
Thermal motor overload can be easily reset from
the 3-button floor level control station
Reliability & Programming
Simplicity
-
Switchless motor eliminates stuck start switch
and motor malfunctions on single-phase operators
-
All high-voltage connections have been removed
from the board for safety and ease of service
-
Diagnostic LEDs speed installation and
troubleshooting
-
Motor direction jumper lets you change motor
direction by simply moving a jumper
Available Plug-in Options for
Logic 3.0 (L3)
Auxiliary
Contact: Used to
operate security, warning, heating or other 5V to 240V
devices. Features both normally open and closed
contacts that actuate in conjunction with limit
switches.
Warning Signal: Red/green light module provides
safety warning prior to close (when using timer-to-close
feature). Also supports audio warning devices and
includes down mid-stop feature.
CPS3 Option: Enables the addition of a second set
of photo-eyes or 2- or 4-wire, self-monitoring edge.
Mechanical Reversing Contactor Circuit
(M): (115V, 208/230V, 460V, 575V,
24V NEC Class 2 Circuit with 40VA transformer)
Industrial linear contactor provides significantly
longer control runs than conventional contactors.
STANDARD FEATURES
Motor: Continuous-duty
high-starting torque motor with instant reverse and
overload protection. Available in 1/3, 1/2, 3/4
and 1 HP; single- or three-phase. Removable without
affecting limit switch settings.
Drive Reduction: First-stage heavy-duty 5L
V-belt; second-stage #41 chain; output on trolley #48
chain on 1/3 and 1/2 HP; #41 chain on 3/4 and 1 HP.
Emergency Disconnect: Spring-loaded for emergency
manual operation.
Wiring Type: B2, C2, D1 and E2 wiring types are
standard and easily set using a selector dial on the
Logic 3.0 Control Board (L3). T and TS wiring can be
activated with use of a CPS-L or CPS-LN4. Reversing
Contactor Units (M) have C2 wiring standard and B2
available by simply moving a jumper wire. Operators are
pre-wired to accept a sensing edge, photoelectric
sensors, radio controls and most types of access control
equipment. Failsafe wiring can be selected with use of a
CPS-L, CPS-LN4 or failsafe edge and CPS3 card.
External Radio Control Terminal: Quick,
convenient connections for retrofitting or adding radio
controls on logic or mechanical operators.
Bearings: Ball bearings on output shaft;
heavy-duty, oil-filled bushings on reduction shafts.
Brake: Solenoid-actuated brake is standard on 3/4
and 1 HP units to prevent coasting of door. Optional on
1/3 and 1/2 HP units.
Friction Clutch: Adjustable, helps protect
against major damage to door and operator should the
door meet an obstruction.
Construction: NEMA 1 type electrical box,
heavy-duty 11-gauge steel frame with durable powdercoat
finish, all reduction sprockets drilled and pinned to
shafts.
Push Button Station: 3-button station comes
standard and has OPEN/CLOSE/STOP functionality.
Quick-Mount Header Bracket: For fast, swing-up
mounting.
Rail Assembly: High-strength dual L-rail track
with nylon quiet-gliding chain guides on rail spacers
for quiet, smooth operation.
Warranty:
2-year warranty
|
 Model J
Industrial
Duty Jackshaft Operator
The Model
J is an industrial-duty jackshaft operator. It
features a removable hinged electrical box
cover, a continuous-duty high-starting torque
motor, industrial ball bearings on the output
shaft and a universal mount frame design.
-
Built-in 3-channel, 315MHz radio receiver
accepts up to 23 Security+® or unlimited DIP
switch remotes. 3-button remotes can be
programmed for OPEN/CLOSE/STOP operation
-
Maintenance Alert System™ establishes a
routine maintenance schedule based on the
number of cycles or calendar date. Includes
self-diagnostic system that allows you to
troubleshoot up to eight different error
codes
-
Timer-to-Close allows programming in 5-sec
or 1-min increments. Commercial or
industrial photo-eyes required
-
Thermal motor overload can be easily reset
from the 3-button floor level control
station
Reliability
& Programming Simplicity
-
Switchless motor eliminates stuck start
switch and motor malfunctions on
single-phase operators
-
All high-voltage connections have been
removed from the board for safety and ease
of service
-
Diagnostic LEDs speed installation and
troubleshooting
-
Motor direction jumper lets you change motor
direction by simply moving a jumper
Available Plug-in Options
for Logic 3.0 (L3)
Auxiliary Contact: Used
to operate security, warning, heating or other
5V to 240V devices. Features both normally
open and closed contacts that actuate in
conjunction with limit switches.
Warning Signal: Red/green light
module provides safety warning prior to close
(when using timer-to-close feature). Also
supports audio warning devices and includes down
mid-stop feature.
CPS3 Option: Enables the
addition of a second set of photo-eyes or 2- or
4-wire, self-monitoring edge.
Mechanical
Reversing Contactor Circuit (M): (115V,
208/230V, 460V, 575V, 24V NEC Class 2 Circuit
with 40VA transformer) Industrial linear
contactor provides significantly longer control
runs than conventional contactors.
STANDARD FEATURES
Motor: Continuous-duty
high-starting torque motor with instant reverse
and overload protection. Available in 1/3,
1/2, 3/4 and 1 HP; single- or three-phase.
Removable without affecting limit switch
settings.
Drive Reduction: First-stage
heavy-duty 5L V-belt; second and third stages
#48 chain; #50 drive chain.
Emergency Disconnect: Easy
emergency manual operation using an electrically
interlocked floor level disconnect.
Wiring Type: B2, C2, D1 and E2
wiring types are standard and easily set using a
selector dial on the Logic 3.0 Control Board
(L3). T and TS wiring can be activated with use
of a CPS-L or CPS-LN4. Reversing Contactor Units
(M) have C2 wiring standard and B2 available by
simply moving a jumper wire. Operators are
pre-wired to accept a sensing edge,
photoelectric sensors, radio controls and most
types of access control equipment. Failsafe
wiring can be selected with use of a CPS-L,
CPS-LN4 or failsafe edge and CPS3 card.
External Radio Control Terminal: Quick,
convenient connections for retrofitting or
adding radio controls on logic or mechanical
operators.
Bearings: Industrial ball
bearings on a 1" output shaft; heavy-duty
oil-filled iron bearings on reduction shafts.
Friction Clutch: Adjustable,
helps protect against major damage to door and
operator should the door meet an obstruction.
Construction: NEMA 1 type
electrical box, heavy-duty 11-gauge steel frame
with durable powdercoat finish, all reduction
sprockets drilled and pinned to shafts.
Push Button Station: 3-button
station comes standard and has OPEN/CLOSE/STOP
functionality.
PosiLock® Mechanical Brake System: Self-locking
mechanical reduction system that functions as a
holding brake.
Warranty:
2-year warranty.
Call (732)
238-4033 for more details
|
|
|
|
